problema con las transferencias de llamadas

. Password Recovery
Command log
Note) If you lost root password or router OS dose not work normally
(OS crashed), you may recovery OS or password under BOOT loader
mode.
Main function of BOOT LOADER
1. root password recovery/change
2. s/w downloading
Enter Bootloader mode>
After power reset or s/w reset, press ctrl-C and ctrl-X key alternately repeatedly, then you
can see “BOOT#” prompt. Note) Check password
BOOT#
Interface Ethernet0, changed state to UP
BOOT# show password
password = router
BOOT#
Note) Change root password (If you want to change from "router" to
"abcd")
BOOT# config
BOOT(config)# passwd abcd abcd
password changed
CF) root password change command under APOS environment(not BOOT
loader)?/b>
(If you want to change from “router” to “abcd”)
router(config)# show user
Login Name Password User Level Timeout
-----------------------------------------------------------------------------------------------
---------
root abcd ADMIN 0
router# config
router(config)# user change root abcd router
router(config)# show user
Login Name Password User Level Timeout
-----------------------------------------------------------------------------------------------
---------
root router ADMIN 0
Note) Upgrade OS image via ftp/tftp under PC or UNIX environment.
ftp
client : 192.71.192.2 (PC)
ftp server: 192.71.192.1 (router) Note) router IP setting (Notice : BOOTER don't refer
configuration value of APOS environment.)
BOOT# config
BOOT(config)# address 192.71.192.1 255.255.255.192
BOOT(config)# end

Note) IP address setting confirm
BOOT# show interface
Interface Configuration : ether0.0
IP address : 192.71.192.1 netmask : 255.255.255.192 mtu = 1500
Ethernet Address : 00 02 a4 99 99 01
Ethernet mode : FULL-DUPLEX
Operating speed : 100 Mbps
Line status : FULL DUPLEX
Operation is UP
Under APOS mode, application image downloading procedure is the
same as BOOT mode.
2. Password recovery & log in BOOT Loader with Boot Loader Version 2.2.5.
· with loader 2.0 or later, you must know APOS root password to login into boot loader mode.
· It has changed for security issue.og. After the login, the all of command is the same as old
version.
· If you lost root password, you can login with guest account. the password is "guest" for this.
· After the login Log in as guest,to recovery password, you may move config mode, then change
password.
· but if you do it, all of configuration will be erased.
step command
1 BOOT_login:
Interface Ethernet0, changed state to DOWN
BOOT_login: guest
BOOT_password:
BOOT> config
BOOT(config)> password router router
If you change the password, your configarion will be erased.
Are you sure you want to continue (y/n)? y
Erasing configuration....done

Password change completed !

gracias por tu rapida respuesta :)
con el 1.4.16

ya medio resolvi el problema, lo que hize fue q:

atxfer=>8
;blidnxfer=># este lo deje como comentario

ahora al marcar 8 en una conversacion me puede hacer una transferencia asistida.
y al marcar # + ext me permite hacer la transferencia a ciegas.

lo raro es que blindxfer, lo tengo deshabilitado y aun asi se puede utilizar (lol)
lo importante es que funciona :D

aprobechando el post, alguien sabe como hacer callpickupss(capturadora de llamadas)?
yo lo hago de la siguiente manera:

features.conf
[general]
pickupexten=*8

sip.conf, iax.conf
[9XXXX]
callgroup=1
pickuogroup=1

con eso supuestamente las extenciones q hago en sip o en iax estan en el mismo grupo para capturar las llamadas pero sin embargo solo puedo capturar llamadas entre telefonos sip, ya que con los iax no me da resultado :S

gracias!